Lately my router seems to be struggling under all my devices and after some googling, it seems my Archer AX1800 isnt really meant for more than 20-40 devices and I’m currently sitting at 50 with heavy torrent traffic and a media server with 15-20 friends and family connected (typically not all at once of course).
I was looking at the Omada networking gear but then thought of trying OPNSense since I have pretty much everything I need on hand versus spending $400+ for the Omada stuff.
I’d like to run it on the media server since I have tons of compute/RAM available but my question is about the ethernet ports. My mobo has a dedicated 2.5Gb ethernet port built in and I have a second 2.5Gb card that I could toss in there as well, but my concern is that I may saturate the ports with all the additional traffic. My LAN is just 1Gb outside of these two PCs.
My other option is an unused Optiplex 3050 micro that I’ve installed a second ethernet port on but these would both be 1Gb ports.
Am I likely to run into saturation issues on the media server or should the 2.5Gb ports be more than enough to handle the load? Apart from the torrents and video streaming, the rest of the network is mostly typical devices like phones/tablets/consoles, 6 4K POE cameras connected to an NVR and frigate, and a bunch of IoT devices connected to Home Assistant.
I don’t necessarily mind using the Optiplex but I’d definitely prefer to keep everything in one place if I can. I realize that this means my network goes down if I restart the host but it has been a pretty rock solid setup and Proxmox means I can just restart individual containers/VMs rather than the host most of the time.
Edit: forgot to mention that I’m open to buying another quad port NIC for the server if recommended, but would definitely prefer to not spend money if possible. I was planning on using the current router in AP mode along with its ports for a switch and I have another 4 port 2.5Gb switch in the mix as well
I have run an OPNsense router like this but not through Proxmox. I did it through virtualization and did a direct PCI passthrough. The main thing is I needed 3 Ethernet ports for this setup to work. It does create at this point as bare metal you can get through virtualization. I am not a network engineer so take what I say with some salt.
I would recommend it but I am confused by some things you have. It sounds more like a switch is needed and the 2.5g to be setup on the LAN side while 1g wan. Most providers don’t go above 1g wan. The router will not be used in an unmanaged switch as it will do direct connections. A managed switch would need some of the traffic to go through the router. The router would only be needed from LAN to WAN.
Main thing is that the internet goes down any time your host updates or router. Booting host then VM can take a few min in some cases.
Level1tech on YouTube has a detailed walkthrough on this type of setup.
Just ask yourself one question: is your household OK with networking going offline when you need to reboot proxmox?
If the answer is yes, then by all means save yourself some hardware and virtualize it.
If the answer is no, then baremetal OPNsense on a miniPC is the way.
This is close to what I did. Cheap little aliexpress 4nic mini pc. Put proxmox on it and one nic is for that, the other three to opnsense. Have one at my home and one at my business and I couldn’t imagine going back. Having proxmox backups in PBS is the only reason I didn’t go bare metal for opnsense. I did all in one for a while, but quickly figured out I was tinkering to much on that box and fixing the internet was hard without internet to ask.
baremetal OPNsense on a miniPC is the way
Can’t recommend Protectli enough. Been running OpnSense on the same Protectli box for over 8 years. It’s a tank.
I’m personally team openwrt. You can find used hardware that can easy do what you need while being highly power efficient and compact.
One word of advise though. I would recommend that you get dedicated access points for wireless if you haven’t already
2.5Gb won’t be your bottleneck on the WAN side — 3-4TB a month is only about 10Mbps averge, and even torrent bursts won’t saturate that unless your internet is over a gig. The place I’d watch is traffic hairpinning through the router, like cameras and media going via OPNsense instead of staying on the switch — keep the NVR/Frigate traffic local where you can.
If you do virtualise it, the security bit that matters most is isolation: keep the WAN side separate from your media containers, and keep the Proxmox managment interface on the LAN only, not reachable from WAN. FYI, that’s also how a misconfigured bridge ends up exposing the host.
And keep your old Archer handy as a fallback router with the OPNsense config backed up — if Proxmox needs a reboot, you can swap one cable and be back online. YMMV, but for a house with 50 devices, I’d rather have that fallback than squeeze everything onto one box.
Depends. How much traffic are you actually pushing at any given time? Don’t you want to be able to get full speed when you’re doing a transfer?
Personally I don’t recommend running a virtual router. If something on the hypervisor breaks, your Internet access goes down too.
I ran OPNSense on a Proxmox VM for a few months and felt nervous about it the whole time. If you’re running a cluster, unless you can do routing without OPNSense, then you can’t get a quorum with the other nodes so restarting that node can require manually force starting the OPNSense VM. Same with a cold startup after a power outage or such.


